Okay, time to get this candle rack finished. Well, almost finished :)
The front of the case has two rails: one at the very top and one at the bottom of the candle till...
Wait! Stop the presses! Thats it! Candle till! CANDLE TILL! Thats what this thing is! The name has appeared! Yes!...just above the drawers. I decided to mould the inside edge of both rails for some visual interest, but I didnt want to get too complex because the candle till :) design is rather understated, in a "Shakerish" kind of way. In the end I went with a simple side bead, and was quite happy with the result.
Heres the tools I used for this step:
The #3 smoothed the surface and edge prior to the moulding being stuck. The 1/4" side bead plane by Andruss (Newark, NJ 1821-41) did what it was made to do over a century and a half ago - amazing!
* The Veritas medium shoulder plane I used to clean up a little tear-out in the quirk shoulder by adding a very tiny bevel to the arris. In front of the planes is the finished rail.
* Side note: Im pretty sure this is one of the original group of planes that started me down the moulding plane path in a big way. You can click on the new "Moulding Plane" link in the "Post Categories" section in the left navbar for more on this topic.
The rails were glued to the case while it was being held in the front vise, allowing easier clamping. Heres a shot of the bottom rail being attached.
The next step was the pediment. In my original plan, the pediment was going to be an ogee or cyma curve. But now I was reconsidering.
I created the blank...
...and toyed with the idea of just going with that. But it didnt feel right - too plain and it didnt fit with the curved front of the case.
So I wanted a curve, which I could have worked out with a batten, as I did with the front, but instead I reached for some curve templates:
What? Doesnt everyone keep a Crock Pot lid and an angle food cake pan handy in the shop?
After tracing both curves on the blank and looking at it on the case, I chose the elliptical curve (Crock Pot). Then it was just a matter of shaping the curve with a drawknife and spokeshave.
After that, it just needed to be glued in place. The only tricky part was I wanted it to be attached before the back went on, so I could use the underside of the top to clamp it. As I wanted the back and the pediment to be flush, this meant I needed to make the back so that I would know how thick it would be and then give the pediment the appropriate overhang.
So, time for the back. I brought the thinner stock left over from resawing the case sides (roughly 1/4" - the sides are 1/2" thick) over to the bench and transferred the dimensions directly. I left it slightly oversized and would plane it flush after it was attached.
I also needed the thin stock for the angled back of the till section, so I made a cardboard mock-up to determine the correct size. The short hunks of dowels, with orange paint streaks from their days as part of a pipe clamp rack, are standing in for candles.
Once I was finished adjusting the cardboard to get the correct angle and fit, I used it as a template and cut the stock with a knife.
This worked great, much better than trying to saw the flexible wood, but I was a little to aggressive and split off a chunk that ran inside the line - drat! Oh well, the candles will hide that reminder to take it easy.
I glued cleats across the back of the stock to stiffen it and flatten out some cupping it was developing. Because this was cross grain, I only glued the middle couple of inches - a bit of an experiment really, well see how it works out.
You can see the pediment, waiting in the background, asking "Werent you just about to glue me on about an hour ago?"
Yeah, yeah. So I did - and then the back.
The back was nailed on, and heres the tool set for that job:
"Whats that? Why yes, that is a 30.06 On A Stick™ and serial #000001 to boot! A true collectors item - thanks for noticing!"
And there it is - just waiting on the drawers...
Final Part VI coming SOON!
